Articles fréquemment consultés
TE0703 - Carrier board for Trenz Electronic modules with 4 x 5 cm form factor (TE0703-07)
Carrier Board for 4 x 5 cm Trenz Electronic SoMs with 3 x Samtec LSHM Series Connectors
Référence de l’article: VAR-827003694
Numéro de produit du fabricant: TE0703-07
Code douane: 84718000
Article situé / expédié de : Riedlingen, Allemagne
The predecessor of this article is TE0703-06. All changes are in the Product Change Notification (PCN).
The Trenz Electronic TE0703 carrier board is a baseboard for 4 x 5 SoMs, which exposes the MIO- and the PS/PL-pins of the SoM to accessible connectors and provides a whole range of on-board-components to test and evaluate Trenz Electronic 4 x 5 SoMs.
See page "4 x 5 cm carriers" to get information about the SoMs supported by the TE0703 carrier board.
Notice
Do not access the FT2232H EEPROM using FTDI programming tools, doing so will erase normally invisible user EEPROM content and invalidate stored AMD/Xilinx JTAG license. Without this license the on-board JTAG will not be accessible any more with any AMD/Xilinx tools. Software tools from FTDI website do not warn or ask for confirmation before erasing user EEPROM content.
Key Features
- On Board
- USB JTAG and UART interface (FTDI FT2232H), compatible withAMD-tools (also with many other tools)
- SDIO port expander with voltage-level translation
- 4 x User LEDs
- D1 and D2 are connected to the carrier controller, their function depends on the firmware
- D3 and D4 are connected to the 4 x 5 module B2B connector pins, and are directly controlled by the module
- 1 x User push button
- Connected to "intelligent Carrier Controller (iCC)" and can be used as module reset button. Other usage possible, actual function depend on the code loaded into iCC
- 6 A high efficiency power SoC DC-DC step-down converter with integrated inductor for 3.3 V power supply
- 4 User DIP switches
- Enable/disable update of the "intelligent Carrier Controller"
- MIO0 (readable signal by iCC and module)
- 2 "mode" bits
- Interface
- Trenz 4 x 5 module socket (3 x Samtec LSHM series connectors)
- Micro SD card connector - Zynq SDIO0 bootable SD port
- 2 x VG96 backplane connectors (mounting holes and solder pads)
- Mini USB connector (USB JTAG and UART interface)
- RJ45 GbE connector
- USB-Host connector
- Power
- Barrel jack for 5V power supply input
- Size
- 6.45x10 cm
Scope of Delivery
- 1 x TE0703-07 carrier board for Trenz Electronic modules with a form factor of 4 x 5 cm
Note: VG96 Connector vertical (article 21545), Harting DIN41612 (female)is not included in the scope of delivery, but can be purchased as an accessory in the shop.
Info: M2.5x8 mm screws and M2.5 galvanized nuts are required for mounting the VG96 connector.
Additional Information
- Manufacturer'sarticle number: TE0703-07
- Trenz Electronic Carrierboard TE0703 Wiki
- Support Forum
All modules produced by Trenz Electronicare developed and manufactured in Germany.
| Caractéristique technique | Valeur |
|---|---|
| ID de l’art. | 103208 |
| État | |
| ID de l'ancien article | 01968567834e713b961d354c1cc1109f |
| Modèle | TE0703-07 |
| Fabricant | |
| Pays de fabrication | Allemagne |
| Contenu | 1 pièce |
| Poids | 151 g |
